[EMS Discuss] Is the 3d printer working?

Mr. Clif EMAIL HIDDEN
Tue Jun 11 09:26:59 PDT 2013


Yes most likely I can. Earlyer is better for me too. :-)

     Clif

Rick Osgood wrote:
> Can either of you guys show up at 5 tonight or a little before to work on
> the printer with me?  I haven't used Slicer at all.  I'm going to try and
> get there by 4:30-4:45 but I might not get there until 5.
>
>
> On Tue, Jun 11, 2013 at 9:15 AM, Mr. Clif<EMAIL HIDDEN>  wrote:
>
>> Tom and I played with it some last night.
>>
>> It was strange that my test parts printed very well, but his looked like
>> they were printed by another poorly adjusted printer. One problem was that
>> the parts weren't sticking very well to the bed but if the bed temp was too
>> high, then the layers wouldn't cool properly and you would get a rubbery
>> mess. I haven't really seen that problem before. I wonder if the green
>> plastic has slightly different properties than the others we were using?
>>
>> Maybe we need to clean the bed or put new tape on it? Skeinforge has
>> better control over bed temp than Slicer, so that might be the one to use
>> for demos.
>>
>>      Clif
>>
>>
>> Rick Osgood wrote:
>>
>>> Are either of you going to be there tomorrow to get the printer going?  I
>>> haven't used it since the upgrade so it will take some learning for me to
>>> get it going.  I'm going to try to get there by 5 if not a little sooner
>>> so
>>> I can try and get it going but it would be nice if someone familiar with
>>> the new version were there too.
>>>
>>> On Monday, June 10, 2013, Bob Miller wrote:
>>>
>>>   I tried to print another wide flat thing Friday night.  One corner
>>>> came off the bed.  If we print small, well-attached things, we should
>>>> be okay.
>>>>
>>>> On Mon, Jun 10, 2013 at 5:48 PM, Mr. Clif<EMAIL HIDDEN<**
>>>> javascript:;>>
>>>>
>>>> wrote:
>>>>
>>>>> I'm not sure how Bob's part came out but I printed something and it was
>>>>> perfect! Granted it was a simple test print. I was hoping to try some
>>>>>
>>>> more
>>>>
>>>>> but may not have time tonight.
>>>>>
>>>>>       Clif
>>>>>
>>>>> Rick Osgood wrote:
>>>>>
>>>>>> I've heard mixed reports lately about the thingomatic.  Is it working?
>>>>>>     KVAL is going to be at EMS tomorrow at 6 to get video of it working
>>>>>> so
>>>>>> we
>>>>>> need to make sure it's in working order.  Can someone please let me
>>>>>>
>>>>> know?
>>>>>     If it's not working I'm going to have to go try and fix it.
>>>>>> Rick
>>>>>>
>>>>>>
>>>>>>
>>>>>> ______________________________**_________________
>>>>>> Discuss mailing list
>>>>>> EMAIL HIDDEN<**javascript:;>
>>>>>>
>>>>>>   http://eugenemakerspace.com/**mailman/listinfo/com.**
>>>> eugenemakerspace.discuss<http://eugenemakerspace.com/mailman/listinfo/com.eugenemakerspace.discuss>
>>>>
>>>>> ______________________________**_________________
>>>>> Discuss mailing list
>>>>> EMAIL HIDDEN<**javascript:;>
>>>>>
>>>>>   http://eugenemakerspace.com/**mailman/listinfo/com.**
>>>> eugenemakerspace.discuss<http://eugenemakerspace.com/mailman/listinfo/com.eugenemakerspace.discuss>
>>>>
>>>>
>>>>
>>>> --
>>>> Bob Miller                              K<bob>
>>>>                                           EMAIL HIDDEN<**
>>>> javascript:;>
>>>>
>>>>



More information about the Discuss mailing list